Trimble FM-750 CFX-750 750 CFX FM Touchscreen OEM - Trimble FM-750 CFX-750 FM750 CFX750 750 CFX FM

Classifieds Home
Previous / Next

Nov 24, 2022 5:01 PM (8440 views)
Clarkfield, MN 56223


Listed for sale are brand new replacement touchscreens for a Trimble 750 FM or CFX Display. If you do not feel comfortable to perform the repair after reviewing my tutorial, I can perform the install for you. Repairs are done the same day the display is delivered and shipped the next day. Turnaround time is roughly 1 week. Just pay shipping both ways. (Majority do the repair themselves).

***Buyer Beware***
I am the only third party supplying genuine OEM touchscreens direct to the farmer. Do not be fooled by other sellers, foreign or domestic. They are peddling counterfeit, inferior, knock off touchscreens. Do not put your farm operation at risk over a few dollars.

A touchscreen replacement will repair finger touch response issues, physical damage etc.
If you have symptoms of no display picture, dim brightness, distorted display image, etc You will need an LCD as well. Contact me regarding LCD replacements.



I also supply other replacement touch screens for various other models such as the Case IH AFS Pro 700, New Holland Intelliview IV, Trimble FMX FM-1000, Trimble FMD, Trimble CFX/FM 750, Ag Leader Integra, Ag Leader Insight. Precision 20/20 Gen 1 or Gen 2. The ad for these screens are listed below:
Ag leader Insight / Trimble FMD Touchscreen
Ag leader Integra Touchscreen
Trimble FMX FM-1000
Ag Leader Versa Touchscreen
Trimble FM-750 CFX-750 750 CFX FM Touchscreen OEM
Case IH AFS Pro 700 / New Holland Intelliview IV Touchscreen
Precision Planting 20/20 Gen 1 or Gen 2 Touchscreen
Trimble / Ag Leader EZ Guide 500 LCD OEM

$340 + Free Shipping Within USA


Quantity discounts available.

I can send paypal invoices or you can use the link below to checkout and purchase via Paypal. The checkout option below is limited to those who reside in the USA. If you reside outside of the USA, please contact me and I can get you a shipping quote. I can then send you a Paypal Invoice that reflects the shipping.


***Checkout and Purchase Now***



Downloadable/Printer Friendly PDF Tutorial



I will provide some installation guidance below if needed.
Install time takes 20-35 minutes.
Touchscreen calibration is required after booting up the display in the settings menu.
Be sure that the display is at room temperature before doing the installation.



*#*Instructions*#*
T15 Torx bit
Phillip Screw driver
Flat Plade screw drivers


Take your flat blade screw driver and remove the rubber side guards as depicted. They pop right off with a little force. You will notice a torx screw is hidden underneath these rubber guards which needs to be removed.


Use torx T15 to remove all screws from the back


Remove this connector to to allow separation from the back enclosure.


1. Disconnect this ribbon cable circled in pink. This is the touch panel's ribbon cable
2. Remove all torx screws circled in yellow
3. Now lift the assembly away from the front bezel
4. Clean and wipe any dust and debris build up from the front bezel
5. Pry the defective touch panel evenly away from the LCD screen. Pry with gentle force. Take your time. Eventually the panel will peel and pop right off.


1. Lay the new touch panel onto the front bezel in the correct orientation so that the ribbon connector and be installed. Try to lay the touch panel onto the front bezel as square as possible.
2. Lay the LCD assembly on top of the touch panel while also keeping the torx screw holes lined up.
3. Evenly tighten torx screws in a criss-cross fashion. Do not over tighten!
4. Reconnect the Ribbon cable for the touch screen panel circled in pink from image above
5. Reconnect the Cable circled in yellow from image above
6. lay the back enclosure on top and fasten the remaining torx screws and press the side rubber guards in place.
7. Power on device and go into the calibration settings.

There is a short cut to get to the screen calibration by pressing and holding the power button and to top brightness button during the boot-up loading screen during the second loading progress bar once it reaches just passed 50%. This is considered a "Soft Reset"

Soft/Hard Reset




This is my technique of replacing the touch screen. These instructions are here to help you build confidence in doing this task. However, I am not liable or responsible for the success of the installation.

Symptoms of a faulty touchscreen:
**The display will boot up to the terms and conditions page and you are unable to press the buttons on the screen to advance to the main screen.
***Certain areas of the touchscreen may work perfectly and certain areas on the touchscreen may not sense your finger presses. The most common area on the touchscreen that gets worn out is the lower right corner. This area of the touchscreen is where we engage/disengage autosteer fuction and where we have to press to advance to the next screen during the bootup of the display.
****You may have to press the touchscreen multiple times for the touchscreen to finally sense your finger presses. This is an early sign that the touchscreen is failing.

*****A unique symptom of a faulty touchscreen is also when you initially bootup the display and you randomly reach a screen that displays an hourglass and a "Finalizing firmware upgrade" "Please wait while the display finalizes the firmware upgrade. This process may take a few minutes." You then get to the point where your finger presses are also not recognized. The touchscreen has "shorted out" and caused a problem with the bootup sequence. A new touchscreen will also fix this problem.


Keywords: Trimble, cfx750, 750 CFX, 750-CFX, 750-FM, FM, FMX, FM1000, touchscreen, touch screen, digitizer, brand new trimble agriculture FM750, OEM, finalizing firmware upgrade, hourglass,


(320)981-0405
[email protected]


***Checkout and Purchase Now***




For Sale
Contact : BigMyke
Email: [email protected]
Ph: (320)981-0405


(Delete all cookies set by this site)